Precision Fukuhara Works, Ltd.｜A circular knitting machine manufacturer boasting a world-class market share
English
Revision History of FMC50
FMC
| Version No. | Previous Version | Date | Contents |
|---|---|---|---|
| Ver 2.3 1.05 | Ver 2.2 1.04 | ’18/04/10 | Add: 1.LEC3DGTY6 Fixed: 1.Improve transfer of pattern by LAN. |
| Ver 2.2 1.04 | Ver 2.1 1.04 | ’18/01/17 | Add: 1.In case of 3POSI, up the B side ACT between the feeder pitch when changing the pattern. (to prevent a momentary tuck) 2.Do not back up if battery low 16 V, warning below 20 V. (Previously do not back up below 20 V) 3.Added yarn table correction function Fixed: 1.Correcting that the striper shifts when executing the striper TEST mode in the transfer machine other than the reset position. |
| Ver 2.1 1.04 | Ver 2.0 1.04 | ’17/04/18 | Add: 1.Addition of angle data correction function in machine data. 2.Using bezel side DIPSW 3 ON, using encoder input noise filter Fixed: 1.Data is not saved when the battery lowers (there is a possibility of failure when saving at low battery) Changed: 1.Stop holding FAN error |
| Ver 2.0 1.04 | Ver 1.9 1.03 | ’17/02/01 | Add: 1.3DGTFY6 machine. 2.Dial Feeder Adjust. Fixed: 1.”ACT ERROR” When it is not divisible With both-side needle selection machines in dial “24ACT”. 2.LAN transfer with both-side needle selection machines. |
| Ver 1.9 1.03 | Ver 1.8 1.03 | ’16/05/31 | Add: 1.Pile machine. Changed: 1.Three times re-“ACT ERROR” to try for the detection. |
| Ver 1.8 1.03 | Ver 1.7 1.03 | ’16/05/31 | Add: 1.Transfer machine. |
| Ver 1.7 1.03 | Ver 1.6 1.03 | ’16/05/31 | Add: 1.Make data in consideration of “NO FINGER INFORMATION” for “ACT DATA” to make beforehand when I do “RESET PARAMETER”. |
| Ver 1.6 1.03 | Ver 1.6 1.02 | ’16/03/16 | Fixed: 1.Failure of the transfer of pattern data using the LAN. |
| Ver 1.6 1.02 | Ver 1.5 1.02 | ’16/03/09 | Add: Dial PSG. Fixed: 1.Cannot install pattern data after memory clear. 2.Reset parameter does not work at the time of the knit handling of both-side needle selection machines. |
| Ver 1.5 1.02 | Ver 1.4 1.02 | ’16/01/25 | Add: Stop it by a “Road Error” when I push the cancellation in a pattern data road. Fixed: When the number of the course of the pattern is smaller than the number of actuators; of the position of “Reset Parameter”< it is for a pattern mistake with the number of some feeders more, and come back to the normal pattern afterwards. |
| Ver 1.4 1.02 | Ver 1.3 1.02 | ’15/12/25 | Fixed: When the number of the course of the pattern is smaller than the number of actuators; of the position of “Reset Parameter” it is for a pattern mistake with the number of some feeders more, and come back to the normal pattern afterwards. |
| Ver 1.3 1.02 | Ver 0.83 1.00 | ’15/12/16 | Fixed: Problem when a dial shifts. Add: 1.Striper machine, both sides needl machine. 2.LAN. |
| Ver 0.83 1.00 | ’15/07/21 | Add: Cylinder needle, both sides needle ( but as for the striper pattern and the garment pattern non-). |