株式会社福原精机制作所|全球第一占有率的在神户生产的圆筒针织机(简称大圆机)制造商

Revision History of FMC50

FMC

Version No.Previous VersionDateContents
Ver 2.3 1.05 Ver 2.2 1.04’18/04/10Add:
1.LEC3DGTY6
Fixed:
1.Improve transfer of pattern by LAN.
 Ver 2.2 1.04 Ver 2.1 1.04’18/01/17Add:
1.In case of 3POSI, up the B side ACT between the feeder pitch when changing the pattern. (to prevent a momentary tuck)
2.Do not back up if battery low 16 V, warning below 20 V. (Previously do not back up below 20 V)
3.Added yarn table correction function
Fixed:
1.Correcting that the striper shifts when executing the striper TEST mode in the transfer machine other than the reset position.
 Ver 2.1 1.04 Ver 2.0 1.04’17/04/18Add:
1.Addition of angle data correction function in machine data.
2.Using bezel side DIPSW 3 ON, using encoder input noise filter
Fixed:
1.Data is not saved when the battery lowers (there is a possibility of failure when saving at low battery)
Changed:
1.Stop holding FAN error
 Ver 2.0 1.04 Ver 1.9 1.03’17/02/01Add:
1.3DGTFY6 machine.
2.Dial Feeder Adjust.
Fixed:
1.”ACT ERROR” When it is not divisible With both-side needle selection machines
 in dial “24ACT”.
2.LAN transfer with both-side needle selection machines.
 Ver 1.9 1.03 Ver 1.8 1.03’16/05/31Add:
1.Pile machine.
Changed:
1.Three times re-“ACT ERROR” to try for the detection.
 Ver 1.8 1.03 Ver 1.7 1.03’16/05/31Add:
1.Transfer machine.
 Ver 1.7 1.03 Ver 1.6 1.03’16/05/31Add:
1.Make data in consideration of “NO FINGER INFORMATION” for “ACT DATA”
to make beforehand when I do “RESET PARAMETER”.
 Ver 1.6 1.03 Ver 1.6 1.02’16/03/16Fixed:
1.Failure of the transfer of pattern data using the LAN.
 Ver 1.6 1.02 Ver 1.5 1.02’16/03/09Add:
Dial PSG.
Fixed:
1.Cannot install pattern data after memory clear.
2.Reset parameter does not work at the time of the knit handling of
  both-side needle selection machines.
 Ver 1.5 1.02 Ver 1.4 1.02’16/01/25Add:
Stop it by a “Road Error” when I push the cancellation in a pattern data road.
Fixed:
When the number of the course of the pattern is smaller than the number of actuators; of the position of “Reset Parameter”< it is for a pattern mistake with the number of some feeders more, and come back to the normal pattern afterwards.
 Ver 1.4 1.02 Ver 1.3 1.02’15/12/25Fixed:
When the number of the course of the pattern is smaller than the number of actuators; of the position of “Reset Parameter” it is for a pattern mistake with the number of some feeders more, and come back to the normal pattern afterwards.
 Ver 1.3 1.02 Ver 0.83 1.00’15/12/16Fixed:
Problem when a dial shifts.
Add:
1.Striper machine, both sides needl machine.
2.LAN.
 Ver 0.83 1.00  ’15/07/21Add:
Cylinder needle, both sides needle ( but as for the striper pattern and the garment pattern non-).