Công ty Precision Fukuhara Works|Là nhà sản xuất máy dệt kim tròn ở Kobe tự hào là thị phần thuộc hàng top đầu trên thế giới.

Other Revision History

Digital Panel ROM

Version No.DateContents
Panel V.H.1.6
(Previous version: Panel V.F.1.6)
2005/03/09Added: 
Monitoring function only for particular customers. (Monitoring output is available when the counter is set to zero.) This version ROM does not apply to ordinary machines.

Software for Auto Striper Controller SCS-V EUT-309AA

Version No.DateContents
V.2.00 1004212010/04/26Changed:  
1) Entry of color data has been simplified by using numeric keys,  e.g. “5A4B” instead of “AAAAABBBB”.
2) If a wrong total number of courses is entered, “COURSE ERROR” message is now displayed and  then  “TOTAL COURSE” entry screen automatically appears.  
V.2.00 0912242010/01/08Changed:  
COLOR ASSIGNMENT for striper data can now be used on EUT-309AA auto striper controller.
V.1.00 0705222007/06/01Added:  
Compatibility with model FX-WSY 30″ having 39 feeders with no gate.
V.1.00 0503292005/03/25Fixed:  
1. Key operation is disabled after the last feeder is taken off and the “KNIT” key is pressed.
2. It is necessary to press the “RESET” key to clear the error signal sent out whenever the power is turned on.
V.1.00 0501212005/03/09Added: 
Combination function which was included in striper controllers of older types.

Option box CPU Program

Version No.DateContents
OCP.SYS V.1.191309192013/09/19Changed:  
1) Half of WAIT at the time of the start of “the optional CPU program”.
OCP.SYS V.1.170812012008/12/01Changed:  
1) Set values such as stitch amount, cam timing timing are now be loaded in the RAM every time the main power is    switched on.
2) Whether the setting in the CPU board is correct can now be monitored by checking the LEDs on the CPU board. (If the    setting is correct,  LEDs 1 to 8 light up.)    
OCP.SYS V.1.130209012002/08/28Changed: 
The original stitch frequency has been changed from 100 (priority is on speed) to 400 (priority is on torque) as there were reports of miss-function of the auto-stitch system.
ROM V.1.02OCP.SYS V.1.120204012002/04/01Changed: 
Now compatible with a new type flash memory (Fujitu-made, 16-bit) as the production of the originally used flash memory has been discontinued. 
ROM V.1.01OCP.SYS V.1.110109172001/09/17Fixed :
Unable to write information on the new Toshiba 32-bit flash memory now used for the option box.

20M/30M LOADER

Version No.DateContents
30M LOADER ULM (Pattern & Parameter) Ver. 5.2 (Prev. Ver. 5.1)2002/06/28Changed:
Both 30M and 20M loaders are now com-patible with Futaba’s display while only the former was  compatible with Futaba’s display in Ver. 5.1.
30M LOADER ULM (Pattern & Parameter) Ver. 5.1(Prev. Ver. 5.0)

30M LOADER ROM       Ver. 1.1(Prev. Ver. 1.0)
2002/01Reason for upgrading :
It has become necessary to be compatible also with Futaba’s display due to discontinuation of the production of NEC’s display.?@
Changed:
Futaba’s display can be used by setting the lowest bit of the 8-bit dip switch to “ON” and NEC’s display can be used with the same dip switch set to  “OFF”.

30M LOADER ROM (Standard)

Version No.DateContents
Ver. 1.22002/06/28Changed:
Now compatible with ULM Ver.5.2 (for both 20M and 30M loaders).
Ver. 1.12002/01Changed:
Now compatible with Futaba’s display.

30M LOADER ROM (2HD)

Version No.DateContents
Ver. 2.12002/06/28Changed:
Now compatible with both NEC’s and Futaba’s display. (For NEC’s display, set the lowest bit of the 8-bit dip switch to “OFF” and for Futaba’s display, set the same bit to “ON”.) 

20M LOADER ROM (NSD-made, Standard)

Version No.DateContents
Ver. 2.62002/06/28Changed:
Now compatible with both NEC’s and Futaba’s display. (For NEC’s display, set the No.7 bit of the 8-bit dip switch to “ON” and for Futaba’s display, set the same bit to “OFF”.  However, no error message is displayed on Futaba’s display.)

20M LOADER (AZ-made, Standard, for Futaba’s diplay)

Version No.DateContents
Ver. 3.62002/06/28Changed:
Now compatible with Futaba’s display. (However, no error message is displayed. Not compatible with NEC’s display.)

20M LOADER (AZ-made, 2HD, for Futaba’s display)

DateContents
Ver. 6022002/06/28Changed:
Now compatible with Futaba’s display. (However, no error message is displayed. Not compatible with NEC’s display.)

LISTCOPY & PARAMETER Progarm

Version No.DateContents
Ver. 2.702016/07/07Fixed:
Windows 10 compatible (LISTCOPY)
Ver. 2.602014/04/14Fixed:
Drive display upper limit of LISTCOPY (20 drive -> 50 drive)
Ver. 2.502012/11/16Added:
WAC Program
Ver. 2.402011/05/31Changed:
Please refer to the changes made from Ver 3.29 to Ver 3.52 ofFDS for Windows.
Ver. 2.302006/11/01Changed:
Please refer to the changes  made from Ver 3.23 to Ver 3.29 ofFDS for Windows.
Ver. 2.102004/05/31Changed:
Parameter has been changed so that the timing data can be entered.
Ver. 2.012002/06/28Added:
Check box “Page Information”.  By checking this box, Thepattern itself  and some data (the title “Fukuhara DesignSystem”,  page and date) are automatically printed out.
Fixed:
1) Overlapping of letters in the preview window.
2) A file cannot be saved after sorting files on LISTCOPY program.
3) Style name cannot be displayed/printed.
Ver. 2.002002/03/01Added:
Disk driver install program in the FDS menu.
Changed:
1) Now compatible with Windows 2000/XP.
2) The number of the parameter color table has been changed     from 12  to 16.
3) Installation folder.
4) Now compatible with the new protect kit (HASP).